König KN-URC10B Instrucciones de operaciones descargar pdf (Pagina 13)

Note :

Orange light indicates that the KN-URC10B is not receiving any signal.

If the signal LED lights up in red, it means that the signal is too weak (too far away) or too strong (too near).

7) You may repeat the steps 3 to 6 to teach (or programme) other buttons. To save and end the learning function,

press the TV Standby button (

) that had been pressed earlier.

Note

If the buttons that have been learnt do not work properly with your equipment, or particularly if only every second

button that you press works, please carry out Advanced Learning.

Learning - Advanced

1) Press and hold the TV Standby button (

) until the LED Signal ( ) ﬂ ashes twice.

2) Enter the code 0 0 1 0 using the numeric buttons. The signal LED ﬂ ashes twice again.

3) Now, the signal LED lights up in green.

4) Press the button on the KN-URC10B remote control that you would like to teach, e.g. OK (

5) The signal LED lights up in orange and indicates that the KN-URC10B remote control is ready to learn.

6) Press and hold the desired button on the original remote control until the green signal LED goes off.

Note

Orange light indicates that the KN-URC10B is not receiving any signal.

If the signal LED lights up in red, it means that the signal is too weak (too far away) or too strong (too near).

7) Press and hold the same button on the original remote control once again until the green signal LED goes off.

8) You may repeat the steps 3 to 7 to teach (or programme) other buttons. To save and end the learning function,

press the TV Standby button (

) that had been pressed earlier.

Button lock

You have the facility for deactivation of individual or not-required functions on the KN-URC10B remote control.

1) Press and hold the TV Standby button (

) until the signal LED ( ) ﬂ ashes twice.

2) Use the number buttons to enter the code 0 0 0 6. The Signal LED ﬂ ashes twice again.

3) Push all the buttons, one after the other, whose functions that you wish to block.

4) Push the TV Standby button (

) to conﬁ rm.

Note

The numbers and the Standby button (

) cannot be blocked.

Note

If you want to reverse the key lock again, you need to fully reset the remote control. See function “Deleting

settings (reset)”.

Code blocking

You can activate the code block to prevent inadvertent programming of the KN-URC10B.

1) Press and hold the TV Standby button (

) until the signal LED ( ) ﬂ ashes twice.

2) Use the number buttons to enter the code 0 0 0 7. The Signal LED ﬂ ashes twice again.

3) The remote control is now blocked for re-programming

Note

The fact that the code block is activated can be seen by the fact that the Signal LED (

) on the KN-URC10B

remote control ﬂ ashes once long instead of twice short.

Note

Please repeat the steps 1 to 3 if you wish to de-activate the code block.

Deleting settings (reset)

1. Press and hold the TV Standby button ( ) until the signal LED ( ) ﬂ ashes twice.

2. Use the number buttons to enter the code 0 0 0 0. Die Signal LED (

) ﬂ ashes twice to conﬁ rm that your

KN-URC10B remote control has been reset.

Note

This “Delete settings (reset)” function means that your KN-URC10B remote control will lose all its programming

and is returned to the as-delivered condition.

BA König KN-URC10B, 135x215 mm, Entwurf 02 CS6.indd 13BA König KN-URC10B, 135x215 mm, Entwurf 02 CS6.indd 13 12.09.2012 08:36:0412.09.2012 08:36:04

1 2 ... 8 9 10 11 12 13 14 15 16 17 18 ... 79 80

Comentarios a estos manuales

Sin comentarios

König KN-URC10B Instrucciones de operaciones Pagina 13

Comentarios a estos manuales

Relacionado con productos y manuales para Controles remotos König KN-URC10B